Network Working Group                                           R. Ogier
Request for Comments: 3684                             SRI International
Category: Experimental                                        F. Templin
                                                                   Nokia
                                                                M. Lewis
                                                       SRI International
                                                           February 2004


    Topology Dissemination Based on Reverse-Path Forwarding (TBRPF)

Status of this Memo

   This memo defines an Experimental Protocol for the Internet
   community.  It does not specify an Internet standard of any kind.
   Discussion and suggestions for improvement are requested.
   Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (2004).  All Rights Reserved.

Abstract

   Topology Dissemination Based on Reverse-Path Forwarding (TBRPF) is a
   proactive, link-state routing protocol designed for mobile ad-hoc
   networks, which provides hop-by-hop routing along shortest paths to
   each destination.  Each node running TBRPF computes a source tree
   (providing paths to all reachable nodes) based on partial topology
   information stored in its topology table, using a modification of
   Dijkstra's algorithm.  To minimize overhead, each node reports only
   *part* of its source tree to neighbors.  TBRPF uses a combination of
   periodic and differential updates to keep all neighbors informed of
   the reported part of its source tree.  Each node also has the option
   to report additional topology information (up to the full topology),
   to provide improved robustness in highly mobile networks.  TBRPF
   performs neighbor discovery using "differential" HELLO messages which
   report only *changes* in the status of neighbors.  This results in
   HELLO messages that are much smaller than those of other link-state
   routing protocols such as OSPF.











Ogier, et al.                 Experimental                      [Page 1]


RFC 3684                         TBRPF                     February 2004


Table of Contents

   1.  Introduction. . . . . . . . . . . . . . . . . . . . . . . . .   3
   2.  Requirements. . . . . . . . . . . . . . . . . . . . . . . . .   4
   3.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   4
   4.  Applicability Section . . . . . . . . . . . . . . . . . . . .   5
   5.  TBRPF Overview. . . . . . . . . . . . . . . . . . . . . . . .   6
       5.1.   Overview of Neighbor Discovery . . . . . . . . . . . .   6
       5.2.   Overview of the Routing Module. .. . . . . . . . . . .   8
   6.  TBRPF Packets . . . . . . . . . . . . . . . . . . . . . . . .  10
       6.1.   TBRPF Packet Header. . . . . . . . . . . . . . . . . .  10
       6.2.   TBRPF Packet Body. . . . . . . . . . . . . . . . . . .  11
              6.2.1.  Padding Options (TYPE = 0 thru 1). . . . . . .  12
              6.2.2.  Messages (TYPE = 2 thru 10). . . . . . . . . .  13
   7.  TBRPF Neighbor Discovery. . . . . . . . . . . . . . . . . . .  13
       7.1.   HELLO Message Format . . . . . . . . . . . . . . . . .  13
       7.2.   Neighbor Table . . . . . . . . . . . . . . . . . . . .  14
       7.3.   Sending HELLO Messages . . . . . . . . . . . . . . . .  15
       7.4.   Processing a Received HELLO Message. . . . . . . . . .  16
       7.5.   Expiration of Timer nbr_life . . . . . . . . . . . . .  18
       7.6.   Link-Layer Failure Notification. . . . . . . . . . . .  18
       7.7.   Optional Link Metrics. . . . . . . . . . . . . . . . .  18
       7.8.   Configurable Parameters. . . . . . . . . . . . . . . .  19
   8.  TBRPF Routing Module. . . . . . . . . . . . . . . . . . . . .  19
       8.1.   Conceptual Data Structures . . . . . . . . . . . . . .  19
       8.2.   TOPOLOGY UPDATE Message Format . . . . . . . . . . . .  21
       8.3.   Interface, Host, and Network Prefix Association
              Message Formats. . . . . . . . . . . . . . . . . . . .  23
       8.4.   TBRPF Routing Operation. . . . . . . . . . . . . . . .  24
              8.4.1.  Periodic Processing. . . . . . . . . . . . . .  24
              8.4.2.  Updating the Source Tree and Topology
                      Graph. . . . . . . . . . . . . . . . . . . . .  25
              8.4.3.  Updating the Routing Table . . . . . . . . . .  26
              8.4.4.  Updating the Reported Node Set . . . . . . . .  27
              8.4.5.  Generating Periodic Updates. . . . . . . . . .  29
              8.4.6.  Generating Differential Updates. . . . . . . .  29
              8.4.7.  Processing Topology Updates. . . . . . . . . .  30
              8.4.8.  Expiring Topology Information. . . . . . . . .  32
              8.4.9.  Optional Reporting of Redundant Topology
                      Information. . . . . . . . . . . . . . . . . .  32
              8.4.10. Local Topology Changes . . . . . . . . . . . .  33
              8.4.11. Generating Association Messages. . . . . . . .  34
              8.4.12. Processing Association Messages. . . . . . . .  36
              8.4.13. Non-Relay Operation. . . . . . . . . . . . . .  37
       8.5.   Configurable Parameters. . . . . . . . . . . . . . . .  38
   9.  TBRPF Flooding Mechanism. . . . . . . . . . . . . . . . . . .  38
   10. Operation of TBRPF in Mobile Ad-Hoc Networks. . . . . . . . .  39
       10.1.  Data Link Layer Assumptions. . . . . . . . . . . . . .  39



Ogier, et al.                 Experimental                      [Page 2]


RFC 3684                         TBRPF                     February 2004


       10.2.  Network Layer Assumptions. . . . . . . . . . . . . . .  39
       10.3.  Optional Automatic Address Resolution. . . . . . . . .  40
       10.4.  Support for Multiple Interfaces and/or
              Alias Addresses. . . . . . . . . . . . . . . . . . . .  40
       10.5.  Support for Network Prefixes . . . . . . . . . . . . .  40
       10.6.  Support for non-MANET Hosts. . . . . . . . . . . . . .  40
       10.7.  Internet Protocol Considerations . . . . . . . . . . .  41
              10.7.1. IPv4 Operation . . . . . . . . . . . . . . . .  41
              10.7.2. IPv6 Operation . . . . . . . . . . . . . . . .  41
   11. IANA Considerations . . . . . . . . . . . . . . . . . . . . .  41
   12. Security Considerations . . . . . . . . . . . . . . . . . . .  42
   13. Acknowledgements. . . . . . . . . . . . . . . . . . . . . . .  42
   14. References. . . . . . . . . . . . . . . . . . . . . . . . . .  42
       14.1.  Normative References . . . . . . . . . . . . . . . . .  42
       14.2.  Informative References . . . . . . . . . . . . . . . .  43
   Authors' Addresses. . . . . . . . . . . . . . . . . . . . . . . .  45
   Full Copyright Statement. . . . . . . . . . . . . . . . . . . . .  46

1.  Introduction

   Topology Dissemination Based on Reverse-Path Forwarding (TBRPF) is a
   proactive, link-state routing protocol designed for mobile ad-hoc
   networks (MANETs), which provides hop-by-hop routing along shortest
   paths to each destination.  Each node running TBRPF computes a source
   tree (providing shortest paths to all reachable nodes) based on
   partial topology information stored in its topology table, using a
   modification of Dijkstra's algorithm.  To minimize overhead, each
   node reports only *part* of its source tree to neighbors.

   TBRPF uses a combination of periodic and differential updates to keep
   all neighbors informed of the reported part of its source tree.  Each
   node also has the option to report addition topology information (up
   to the full topology), to provide improved robustness in highly
   mobile networks.

   TBRPF performs neighbor discovery using "differential" HELLO messages
   which report only *changes* in the status of neighbors.  This results
   in HELLO messages that are much smaller than those of other link-
   state routing protocols such as OSPF [6].

   TBRPF consists of two modules: the neighbor discovery module and the
   routing module (which performs topology discovery and route
   computation).  An overview of these modules is given in Section 5.








Ogier, et al.                 Experimental                      [Page 3]


RFC 3684                         TBRPF                     February 2004


2.  Requirements

   The keywords "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL", when
   they appear in this document, are to be interpreted as described in
   BCP 14, RFC 2119 [1].

   This document also makes use of internal conceptual variables to
   describe protocol behavior and external variables that an
   implementation must allow system administrators to change.  The
   specific variable names, how their values change, and how their
   settings influence protocol behavior are provided to demonstrate
   protocol behavior.  An implementation is not required to have them in
   the exact form described here, so long as its external behavior is
   consistent with that described in this document.

3.  Terminology

   The following terms are used to describe TBRPF:

   node
      A router that implements TBRPF.

   router ID
      Each node is identified by a unique 32-bit router ID (RID), which
      for IPv4 is typically equal to the IP address of one of its
      interfaces.  The term "node u" denotes the node whose RID is equal
      to u.

   interface
      A node's attachment to a communication facility or medium through
      which it can communicate with other nodes.  A node can have
      multiple interfaces.  An interface can be wireless or wired, and
      can be broadcast (e.g., Ethernet) or point-to-point.  Each
      interface is identified by its IP address.  The term "interface I"
      denotes the interface whose IP address is I.

   link
      A link is an ordered pair of interfaces (I,J) where I and J are on
      two different nodes, and where interface I has recently received
      packets sent from interface J.  A link (i,j) from node i to node j
      is said to exist if node i has an interface I and node j has an
      interface J such that (I,J) is a link.  Nodes i and j are called
      the "tail" and "head" of the link, respectively.

   bidirectional link
      A link (I,J) such that interfaces I and J can both hear each
      other.  Also called a 2-way link.



Ogier, et al.                 Experimental                      [Page 4]


RFC 3684                         TBRPF                     February 2004


   neighbor node
      A node j is said to be a neighbor of node i if node i can hear
      node j on some interface.  Node j is said to be a 2-way neighbor
      if there is a bidirectional link between i and j.

   MANET interface
      Any wireless interface such that two neighbor nodes on the
      interface need not be neighbors of each other.  MANET nodes
      typically have at least one MANET interface, but this is not a
      requirement.

   topology
      The topology of the network is described by a graph G = (V, E),
      where V is the set of nodes u and E is the set of links (u,v) in
      the network.

   source tree
      The directed tree (denoted T) computed by each node that provides
      shortest paths to all other reachable nodes.

   topology update
      A message that reports the state of one or more links.

   parent
      The parent of node i for node u is the next node on the computed
      shortest path from node i to node u.

   predecessor
      The predecessor of a node v on the source tree is the node u such
      that the link (u,v) is in the source tree.

   leaf node
      A leaf node of the source tree is a node on the source tree that
      is not the predecessor of any other node on the source tree.

   proactive routing protocol
      A routing protocol in which each node maintains routes to all
      reachable destinations at all times, whether or not there is
      currently any need to deliver packets to those destinations.  In
      contrast, an "on-demand" routing protocol discovers and maintains
      routes only when they are needed.

4.  Applicability Section

   TBRPF is a proactive routing protocol designed for mobile ad-hoc
   networks (MANETs).  It can support networks with up to a few hundred
   nodes, and can be combined with hierarchical routing techniques to
   support much larger networks.  Because it employs techniques to



Ogier, et al.                 Experimental                      [Page 5]


RFC 3684                         TBRPF                     February 2004


   greatly reduce control traffic, TBRPF can support much larger and
   denser networks than routing protocols based on the classical link-
   state algorithm (e.g., OSPF).

   The number of nodes that can be supported depends on several factors,
   including the MAC data rate, the rate of topology changes, and the
   network density (average number of neighbors).  Simulations have been
   reported in which TBRPF has supported as many as 500 nodes.  In
   simulations with 100 nodes and 20 traffic streams (sources), using
   IEEE 802.11 with a data rate of 2 Mbps, TBRPF was found to generate
   approximately 80-120 kb/s of routing control traffic for the
   scenarios considered, which compared favorably with other MANET
   routing protocols [7][8].  A proof of correctness for TBRPF can be
   found in references [8] and [9].

5.  TBRPF Overview

   TBRPF consists of two main modules: the neighbor discovery module,
   and the routing module (which performs topology discovery and route
   computation).

5.1.  Overview of Neighbor Discovery

   The TBRPF Neighbor Discovery (TND) protocol allows each node i to
   quickly detect the neighbor nodes j such that a bidirectional link
   (I,J) exists between an interface I of node i and an interface J of
   node j.  The protocol also quickly detects when a bidirectional link
   breaks or becomes unidirectional.

   The key feature of TND is that it uses "differential" HELLO messages
   which report only *changes* in the status of links.  This results in
   HELLO messages that are much smaller than those of other link-state
   routing protocols such as OSPF, in which each HELLO message includes
   the IDs of *all* neighbors.  As a result, HELLO messages can be sent
   more frequently, which allows faster detection of topology changes.

   TND is designed to be fully modular and independent of the routing
   module.  TND performs ONLY neighbor sensing, i.e., it determines
   which nodes are (1-hop) neighbors.  In particular, it does not
   discover 2-hop neighbors (which is handled by the routing module).
   As a result, TND can be used by other routing protocols, and TBRPF
   can use another neighbor discovery protocol in place of TND, e.g.,
   one provided by the link layer.

   Nodes with multiple interfaces run TND separately on each interface,
   similar to OSPF.  Thus, a neighbor table is maintained for each local
   interface, and a HELLO sent on a particular interface contains only
   information regarding neighbors heard on that interface.



Ogier, et al.                 Experimental                      [Page 6]


RFC 3684                         TBRPF                     February 2004


   We note that, in wireless networks, it is possible for a single
   interface I to receive packets from multiple interfaces J associated
   with the same neighbor node.  This could happen, for example, if the
   neighbor uses a directional antenna with different interfaces
   representing different beams.  For this reason, TBRPF includes
   neighbor interface addresses in HELLO messages, unlike OSPF, which
   includes only router IDs in HELLO packets.

   Each TBRPF node maintains a neighbor table for each local interface
   I, which stores state information for each neighbor interface J heard
   on that interface, i.e., for each link (I,J) between interface I and
   a neighbor interface J.  The status of each link can be 1-WAY, 2-WAY,
   or LOST.  The neighbor table for interface I determines the contents
   of HELLO messages sent on interface I, and is updated based on HELLO
   messages received on interface I (and possibly on link-layer
   notifications).

   Each TBRPF node sends (on each interface) at least one HELLO message
   per HELLO_INTERVAL.  Each HELLO message contains three (possibly
   empty) lists of neighbor interface addresses (which are formatted as
   three message subtypes): NEIGHBOR REQUEST, NEIGHBOR REPLY, and
   NEIGHBOR LOST.  Each HELLO message also contains the current HELLO
   sequence number (HSEQ), which is incremented with each transmitted
   HELLO.

   In the following overview of the operation of TND, we assume that
   interface I belongs to node i, and interface J belongs to node j.
   When a node i changes the status of a link (I,J), it includes the
   neighbor interface address J in the appropriate list (NEIGHBOR
   REQUEST/REPLY/LOST) in at most NBR_HOLD_COUNT (typically 3)
   consecutive HELLOs sent on interface I.  This ensures that node j
   will either receive one of these HELLOs on interface J, or will miss
   NBR_HOLD_COUNT HELLOs and thus declare the link (J,I) to be LOST.
   This technique makes it unnecessary for a node to include each 1-WAY
   or 2-WAY neighbor in HELLOs indefinitely, unlike OSPF.

   To avoid establishing a link that is likely to be short lived (i.e.,
   to employ hysteresis), node i must receive (on interface I) at least
   HELLO_ACQUIRE_COUNT (e.g., 2) of the last HELLO_ACQUIRE_WINDOW (e.g.,
   3) HELLOs sent from a neighbor interface J, before declaring the link
   (I,J) to be 1-WAY.  When this happens, node i includes J in the
   NEIGHBOR REQUEST list in each of its next NBR_HOLD_COUNT HELLO
   messages sent on interface I, or until a NEIGHBOR REPLY message
   containing I is received on interface I from neighbor interface J.

   If node j receives (on interface J) one of the HELLOs sent from
   interface I that contains J in the NEIGHBOR REQUEST list, then node j
   declares the link (J,I) to be 2-WAY (unless it is already 2-WAY), and



Ogier, et al.                 Experimental                      [Page 7]


RFC 3684                         TBRPF                     February 2004


   includes I in the NEIGHBOR REPLY list in each of its next
   NBR_HOLD_COUNT HELLO messages sent on interface J.  Upon receiving
   one of these HELLOs on interface I, node i declares the link (I,J) to
   be 2-WAY.

   If node i receives a HELLO on interface I, sent from neighbor
   interface J, whose HSEQ indicates that at least NBR_HOLD_COUNT HELLOs
   were missed, or if node i receives no HELLO on interface I sent from
   interface J within NBR_HOLD_TIME seconds, then node i changes the
   status of link (I,J) to LOST (unless it is already LOST), and
   includes J in the NEIGHBOR LOST list in each of its next
   NBR_HOLD_COUNT HELLO messages sent on interface I (unless the link
   changes status before these transmissions are complete).  Node j will
   either receive one of these HELLOs on interface J or will miss
   NBR_HOLD_COUNT HELLOs; in either case, node j will declare the link
   (J,I) to be LOST.  In this manner, both nodes will agree that the
   link between I and J is no longer bidirectional, even if node j can
   still hear HELLOs from node i.

   Each node may maintain and update one or more link metrics for each
   link (I,J) from a local interface I to a neighbor interface J,
   representing the quality of the link.  Such link metrics can be used
   as additional conditions for changing the status of a neighbor, based
   on the link metric going above or below some threshold.  TBRPF also
   allows link metrics to be advertised in topology updates, and to be
   used for computing shortest paths.

5.2.  Overview of the Routing Module

   Each node running TBRPF maintains a source tree, denoted T, which
   provides shortest paths to all reachable nodes.  Each node computes
   and updates its source tree based on partial topology information
   stored in its topology table, using a modification of Dijkstra's
   algorithm.  To minimize overhead, each node reports only part of its
   source tree to neighbors.  The main idea behind the current version
   of TBRPF came from PTSP [10], another protocol in which each node
   reports only part of its source tree.  (However, TBRPF differs from
   PTSP in several ways.)  The current version of TBRPF should not be
   confused with its previous version [11], which is a full-topology
   routing protocol.

   The part of T that a node reports to neighbors is called the
   "reported subtree" and is denoted RT.  Each node reports RT to
   neighbors in *periodic* topology updates (e.g., every 5 seconds), and
   reports changes (additions and deletions) to RT in more frequent
   *differential* updates (e.g., every 1 second).  Periodic updates
   inform new neighbors of RT, and ensure that each neighbor eventually
   learns RT even if it does not receive all updates.  Differential



Ogier, et al.                 Experimental                      [Page 8]


RFC 3684                         TBRPF                     February 2004


   updates ensure the fast propagation of each topology update to all
   nodes that are affected by the update.  A received topology update is
   not forwarded, but *may* result in a change to RT, which will be
   reported in the next differential or periodic update.  Whenever
   possible, topology updates are included in the same packet as a HELLO
   message, to minimize the number of control packets sent.  TBRPF does
   not require reliable or sequenced delivery of messages, and does not
   use ACKs or NACKs.

   TBRPF supports multiple interfaces, associated hosts, and network
   prefixes.  Information regarding associated interfaces, hosts, and
   prefixes is disseminated efficiently in periodic and differential
   updates, similar to the dissemination of topology updates.

   The reported subtree RT consists of links (u,v) of T such that u is
   in the "reported node set" RN, which is computed as follows.  Node i
   includes a neighbor j in RN if and only if node i determines that one
   of its neighbors may select i to be its next hop on its shortest path
   to j.  To make this determination, node i computes the shortest
   paths, up to 2 hops, from each neighbor to each other neighbor, using
   only neighbors (or node i itself) as an intermediate node, and using
   relay priority (included in HELLO messages) and router ID to break
   ties.  After a node determines which neighbors are in RN, each
   reachable node u is included in RN if and only if the next hop on the
   shortest path to u is in RN.  A node also includes itself in RN.  As
   a result, the reported subtree RT includes the subtrees of T that are
   rooted at neighbors in RN, and also includes all local links to
   neighbors.

   We note that neighbors in RN are analogous to multipoint relay (MPR)
   selectors [12].  Thus, if node i selects neighbor j to be in RN, then
   node i effectively selects itself to be an MPR of node j.  This is
   quite different from [12], in which a node does not select itself to
   be an MPR, but selects a subset of its neighbors to be MPRs.

   A node with a larger relay priority reports a larger part of its
   source tree (on average), and is more likely to be selected as a
   next-hop relay by its neighbors.  A node with relay priority equal to
   0 is called a non-relay node, and never forwards packets originating
   from other nodes.

   TBRPF does not use sequence numbers for topology updates, thus
   reducing message overhead and avoiding wraparound problems.  Instead,
   a technique similar to SPTA [13] is used in which, for each link
   (u,v) reported by one or more neighbors, only the next hop p(u) to u
   is believed regarding the state of the link.  (However, in SPTA each
   node reports the full topology.)  Using this technique, each node
   maintains a topology graph TG, consisting of links that are believed



Ogier, et al.                 Experimental                      [Page 9]


RFC 3684                         TBRPF                     February 2004


   to be up, and computes T as the shortest-path tree within TG.  To
   allow immediate rerouting, the restriction that each link (u,v) in TG
   must be reported by p(u) is relaxed temporarily if p(u) changes to a
   neighbor that is not reporting the link.

   Each node is required to report RT, but may report additional links,
   e.g., to provide increased robustness in highly mobile networks.
   More precisely, a node may maintain any subgraph H of TG that
   contains T, and report the reported subgraph RH, which consists of
   links (u,v) of H such that u is in RN.  For example, H can equal TG,
   which would provide each node with the full network topology if this
   is done by all nodes.  H can also be a biconnected subgraph that
   contains T, which would provide each node with two disjoint paths to
   each other node, if this is done by all nodes.

   TBRPF allows the option to include link metrics in topology updates,
   and to compute paths that are shortest with respect to the metric.
   This allows packets to be sent along paths that are higher quality
   than minimum-hop paths.

   TBRPF allows path optimality to be traded off in order to reduce the
   amount of control traffic in networks with a large diameter, where
   the degree of approximation is determined by the configurable
   parameter NON_TREE_PENALTY.

6.  TBRPF Packets

   Nodes send TBRPF protocol data in contiguous units known as packets.
   Each packet includes a header, optional header extensions, and a body
   comprising one or more messages and padding options as needed.  To
   facilitate efficient receiver processing, senders SHOULD insert
   padding options as necessary to align multi-octet words within the
   TBRPF packet on natural boundaries (i.e., modulo-8/4/2 addresses for
   64/32/16-bit words, respectively).  Receivers MUST be capable of
   processing multi-octet words whether or not aligned on natural
   boundaries.  The following sections specify elements of the TBRPF
   packet in more detail.

6.1.  TBRPF Packet Header

   TBRPF packet headers are variable-length (minimum one octet).  The
   format for the packet header is as follows:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |  Vers |L|I|R|R|   Reserved    |      Header Extensions ...
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+



Ogier, et al.                 Experimental                     [Page 10]


RFC 3684                         TBRPF                     February 2004


   Version (4 bits)
      The TBRPF version number.  This specification documents version 4
      of the protocol.

   Flags (4 bits)
      Two bits (L,I) specify which header extensions (if any) follow.
      Two bits (R) are reserved for future use, and MUST be zero.  Any
      extensions specified by these bits MUST appear in the same order
      as the bits (i.e., first L, then I) as follows:

   L - Length included
      If the underlying delivery service provides a length field, the
      sender MAY set L = '0' and omit the length extension.  Otherwise,
      the sender MUST set L = '1' and include a 16-bit unsigned integer
      length immediately after any previous header field.  The length
      includes all header and data bytes and is written into the length
      field in network byte order.

      Receivers examine the L bit to determine whether the length field
      is present.  If L = '1', the receiver reads the length field to
      determine the length of the TBRPF packet, including the TBRPF
      packet header.  Receivers discard any TBRPF packet if neither the
      underlying delivery service nor the TBRPF packet header provide
      packet length.

   I - Router ID (RID) included
      If the underlying delivery service encodes the sender's RID, the
      sender MAY set I = '0' and omit the RID field.  Otherwise, the
      sender MUST set I = '1' and include a 4-octet RID in network byte
      order immediately after any previous header fields.  The RID
      option provides a mechanism for implicit network-level address
      resolution.  A receiver that detects a RID option SHOULD create a
      binding between the RID and the source address that appears in the
      network-level header.

   Reserved
      Reserved for future use; MUST be zero.

6.2.  TBRPF Packet Body

   The TBRPF packet body consists of the concatenation of one or more
   TBRPF messages (and padding options where necessary).  Messages and
   padding options within the TBRPF packet body are encoded using the
   following format:

   +-+-+-+-+-+-+-+-+- - - - -
   |OPTIONS| TYPE  | VALUE
   +-+-+-+-+-+-+-+-+- - - - -



Ogier, et al.                 Experimental                     [Page 11]


RFC 3684                         TBRPF                     February 2004


   OPTIONS (4 bits)
      Four option bits that depend on TYPE.

   TYPE (4 bits)
      Identifier for message type or padding option.

   VALUE
      Variable-length field.  (Format and length depend on TYPE, as
      described in the following sections.)

   The sequence of elements MUST be processed strictly in the order they
   appear within the TBRPF packet body; a receiver must not, for
   example, scan through the packet body looking for a particular type
   of element prior to processing all preceding elements [2].  TBRPF
   packet elements include padding options and messages as described
   below.

6.2.1.  Padding Options (TYPE = 0 thru 1)

   Senders MAY insert two types of padding options where necessary,
   e.g., to satisfy alignment requirements for other elements [2].
   Padding options may occur anywhere within the TBRPF packet body.  The
   following two padding options are defined:

    Pad1 option (TYPE = 0)

   +-+-+-+-+-+-+-+-+
   |   0   |   0   |
   +-+-+-+-+-+-+-+-+

   The Pad1 option inserts one octet of padding into the TBRPF packet
   body; the VALUE field is omitted.  If more than one octet of padding
   is required, the PadN option (described next) should be used, rather
   than multiple Pad1 options.

    PadN option (TYPE = 1)

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- - - - - - - - - - -
   |   0   |   1   |      LEN      |  Zero-valued Octets
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- - - - - - - - - - -

   The PadN option inserts two or more octets of padding into the TBRPF
   packet body.  The first octet of the VALUE field contains an 8-bit
   unsigned integer length containing a value between 0 - 253 which
   specifies the number of zero-valued octets that immediately follow,
   yielding a maximum total of 255 padding octets.





Ogier, et al.                 Experimental                     [Page 12]


RFC 3684                         TBRPF                     February 2004


6.2.2.  Messages (TYPE = 2 thru 10)

   Additional message types are described as they occur in the following
   sections.  Senders encode messages as specified by the individual
   message formats.  Receivers detect errors in message construction,
   e.g., messages with unrecognized types, messages with a non-integral
   number of elements, or with fewer elements than indicated, etc.  In
   all cases, upon detecting an error, the receiver MUST discontinue
   processing the current TBRPF packet and discard any unprocessed
   elements.

7.  TBRPF Neighbor Discovery

   This section describes the TBRPF Neighbor Discovery (TND) protocol,
   which allows each node to quickly detect bidirectional links (I,J)
   between a local interface I and a neighbor interface J, and to
   quickly detect the loss of such links.  The interface between TND and
   the routing module is defined by the neighbor table maintained by TND
   and the three procedures Link_Up(I,J), Link_Down(I,J), and
   Link_Change(I,J), which are called by TND to announce a new link, the
   loss of a link, and a change in the metric of a link, respectively.

7.1.  HELLO Message Format

   The HELLO message has the following three subtypes:

   -  NEIGHBOR REQUEST (TYPE = 2)
   -  NEIGHBOR REPLY (TYPE = 3)
   -  NEIGHBOR LOST (TYPE = 4)

   Each HELLO subtype has the following format:

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |   0   | TYPE  |     HSEQ      |  Pri  |          n            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Neighbor Interface Address (1)                  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Neighbor Interface Address (2)                  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   ~                              ...                              ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Neighbor Interface Address (n)                  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   HSEQ (8 bits)
      The HELLO sequence number.





Ogier, et al.                 Experimental                     [Page 13]


RFC 3684                         TBRPF                     February 2004


   Pri (4 bits)
      This field indicates the sending node's relay priority, which is
      an integer between 0 and 15.  A node with a higher relay priority
      is more likely to be selected as the next hop on a route.  The
      value 0 is reserved for non-relay nodes, i.e., nodes that should
      never forward packets originating from other nodes.  A router in
      normal operation SHOULD have a relay priority equal to 7.  A
      router can change its relay priority dynamically, e.g., when its
      power supply becomes critical.

   n (12 bits)
      The number of 32-bit neighbor interface addresses in the message.

   A HELLO message is the concatenation of a NEIGHBOR REQUEST message, a
   NEIGHBOR REPLY message, and a NEIGHBOR LOST message, where each of
   the last two messages is omitted if its list of neighbor interface
   addresses is empty.  Thus, a HELLO message always includes a
   (possibly empty) NEIGHBOR REQUEST.

7.2.  Neighbor Table

   Each node maintains, for each of its local interfaces I, a neighbor
   table, which stores state information for each neighbor interface J
   from which HELLO messages have recently been received by interface I.
   The entry for neighbor interface J, in the neighbor table for I,
   contains the following variables:

      nbr_rid(I,J) - The router ID of the node associated with neighbor
      interface J.

      nbr_status(I,J) - The current status of the link (I,J), which can
      be LOST, 1-WAY, or 2-WAY.

      nbr_life(I,J) - The amount of time (in seconds) remaining before
      nbr_status(I,J) must be changed to LOST if no further HELLO
      message from interface J is received.  Set to NBR_HOLD_TIME
      whenever a HELLO is received on interface I from interface J.

      nbr_hseq(I,J) - The value of HSEQ in the last HELLO message
      received on interface I from interface J.  Used to determine the
      number of HELLOs that have been missed.

      nbr_count(I,J) - The remaining number of times a NEIGHBOR REQUEST/
      REPLY/LOST message containing J must be sent on interface I.

      hello_history(I,J) - A list of the sequence numbers of the last
      HELLO_ACQUIRE_WINDOW HELLO messages received on interface I from
      interface J.



Ogier, et al.                 Experimental                     [Page 14]


RFC 3684                         TBRPF                     February 2004


      nbr_metric(I,J) - An optional measure of the quality of the link
      (I,J), represented by an integer between 1 and 255, where smaller
      values indicate better quality.  Defaults to 1 if not used.

      nbr_pri(I,J) - The relay priority of the node associated with
      interface J.

   The entry for interface J in the neighbor table for interface I may
   be deleted if no HELLO has been received on interface I from
   interface J within the last 2*NBR_HOLD_TIME seconds.  (It is kept
   while NEIGHBOR LOST messages containing J are being transmitted.)
   The absence of an entry for a given interface J is equivalent to an
   entry with nbr_status(I,J) = LOST and hello_history(I,J) = NULL.

   The three possible values of nbr_status(I,J) have the following
   informal meanings (the exact meanings are defined by the protocol):

   LOST
      Interface I has not received a sufficient number of HELLO messages
      recently from Interface J.

   1-WAY
      Interface I has received a sufficient number of HELLO messages
      recently from Interface J, but the link is not 2-WAY.

   2-WAY
      Interfaces I and J have both received a sufficient number of HELLO
      messages recently from each other.

7.3.  Sending HELLO Messages

   Each node MUST send, on each local interface, at least one HELLO
   message per HELLO_INTERVAL.  HELLO messages MAY be sent more
   frequently than this (e.g., for faster detection of topology
   changes).  However, to avoid the possibility that HSEQ wraps around
   to the same number before a neighbor that stops receiving HELLO
   messages changes the status of the link to LOST, the time between two
   consecutive HELLO messages (sent on a given interface) MUST be
   greater than NBR_HOLD_TIME/128 second.

   To avoid synchronization of control messages, which can result in
   collisions, HELLO messages SHOULD NOT be transmitted at equal
   intervals.  To achieve this, a node MAY choose the interval between
   consecutive HELLO messages to be HELLO_INTERVAL - jitter, where
   jitter is selected randomly from the interval [0, MAX_JITTER].






Ogier, et al.                 Experimental                     [Page 15]


RFC 3684                         TBRPF                     February 2004


   Each HELLO message always includes a NEIGHBOR REQUEST message, even
   if its list of neighbor addresses is empty.  The NEIGHBOR REQUEST
   message includes the sequence number HSEQ, which is incremented by 1
   (modulo 256) each time a HELLO is sent.  The HELLO message also
   includes a NEIGHBOR REPLY message if its list of neighbor addresses
   is nonempty, and a NEIGHBOR LOST message if its list of neighbor
   addresses is nonempty.  The contents of these three messages are
   determined by the following steps at node i for each interface I:

   1. For each interface J such that nbr_status(I,J) = LOST and
      nbr_count(I,J) > 0, include J in the NEIGHBOR LOST message and
      decrement nbr_count(I,J).

   2. For each interface J such that nbr_status(I,J) = 1-WAY and
      nbr_count(I,J) > 0, include J in the NEIGHBOR REQUEST message and
      decrement nbr_count(I,J).

   3. For each interface J such that nbr_status(I,J) = 2-WAY and
      nbr_count(I,J) > 0, include J in the NEIGHBOR REPLY message and
      decrement nbr_count(I,J).

   If a node restarts, so that all entries are removed from the neighbor
   table, then the node MUST ensure that (for each interface) at least
   one of the following two conditions is satisfied:

   1. The difference between the transmission times of the first HELLO
      sent after restarting and the last HELLO sent before restarting is
      at least 2*NBR_HOLD_TIME.

   2. Letting HSEQ_LAST denote the sequence number of the last HELLO
      that was sent before restarting, the sequence number of the first
      HELLO sent after restarting is set to HSEQ_LAST + NBR_HOLD_COUNT +
      1 (modulo 256).

   Either of these conditions ensures that, if node i with interface I
   restarts, then each neighbor of node i that has a link (J,I) to
   interface I will set the status of the link to LOST.

7.4.  Processing a Received HELLO Message

   When a node receives a HELLO message, it obtains the IP address of
   the sending interface from the IP header.  If the TBRPF packet header
   of the received HELLO contains the RID option, then the RID of the
   sending node is obtained from the TBRPF packet header; otherwise it
   is equal to the IP address of the sending interface.  If node i (with
   RID equal to i) receives a HELLO message on interface I, sent by node
   j (with RID equal to j) on interface J, with sequence number HSEQ and
   relay priority PRI, then node i performs the following steps:



Ogier, et al.                 Experimental                     [Page 16]


RFC 3684                         TBRPF                     February 2004


   1. If the neighbor table for interface I does not contain an entry
      for interface J, create one with nbr_rid(I,J) = j, nbr_status(I,J)
      = LOST (temporarily), nbr_count(I,J) = 0, and nbr_hseq(I,J) =
      HSEQ.

   2. Update hello_history(I,J) to reflect the received HELLO message.
      If nbr_hseq(I,J) > HSEQ (due to wraparound), set nbr_hseq(I,J) =
      nbr_hseq(I,J) - 256.

   3. If nbr_status(I,J) = LOST and hello_history(I,J) indicates that
      HELLO_ACQUIRE_COUNT of the last HELLO_ACQUIRE_WINDOW HELLO
      messages from interface J have been received:

      a. If interface I does not appear in the NEIGHBOR REQUEST list or
         the NEIGHBOR REPLY list, set nbr_status(I,J) = 1-WAY and
         nbr_count(I,J) = NBR_HOLD_COUNT.

      b. Else, set nbr_status(I,J) = 2-WAY and nbr_count(I,J) =
         NBR_HOLD_COUNT. Call Link_Up(I,J).

   4. Else, if nbr_status(I,J) = 1-WAY:

      a. If HSEQ - nbr_hseq(I,J) > NBR_HOLD_COUNT, then set
         nbr_status(I,J) = LOST and nbr_count(I,J) = NBR_HOLD_COUNT.

      b. Else, if interface I appears in the NEIGHBOR REQUEST list, set
         nbr_status(I,J) = 2-WAY and nbr_count(I,J) = NBR_HOLD_COUNT.
         Call Link_Up(I,J).

      c. Else, if interface I appears in the NEIGHBOR REPLY list, set
         nbr_status(I,J) = 2-WAY and nbr_count(I,J) = 0.  Call
         Link_Up(I,J).

   5. Else, if nbr_status(I,J) = 2-WAY:

      a. If interface I appears in the NEIGHBOR LOST list, set
         nbr_status(I,J) = LOST and nbr_count(I,J) = 0.  Call
         Link_Down(I,J).

      b. Else, if HSEQ - nbr_hseq(I,J) > NBR_HOLD_COUNT, set
         nbr_status(I,J) = LOST and nbr_count(I,J) = NBR_HOLD_COUNT.
         Call Link_Down(I,J).

      c. Else, if interface I appears in the NEIGHBOR REQUEST list and
         nbr_count(I,J) = 0, set nbr_count(I,J) = NBR_HOLD_COUNT.

   6. Set nbr_life(I,J) = NBR_HOLD_TIME, nbr_hseq(I,J) = HSEQ, and
      nbr_pri(I,J) = PRI.



Ogier, et al.                 Experimental                     [Page 17]


RFC 3684                         TBRPF                     February 2004


7.5.  Expiration of Timer nbr_life

   Upon expiration of the timer nbr_life(I,J) in the neighbor table for
   interface I, node i performs the following step:

      If nbr_status(I,J) = 1-WAY or 2-WAY, set nbr_status(I,J) = LOST
      and nbr_count(I,J) = NBR_HOLD_COUNT.  Call Link_Down(I,J).

7.6.  Link-Layer Failure Notification

   Some link-layer protocols (e.g., IEEE 802.11) provide a notification
   that the link to a particular neighbor has failed, e.g., after
   attempting a maximum number of retransmissions.  If such an
   notification is provided by the link layer, then node i SHOULD
   perform the following step upon receipt of a link-layer failure
   notification for the link (I,J) from local interface I to neighbor
   interface J:

      If nbr_status(I,J) = 2-WAY, set nbr_status(I,J) = LOST and
      nbr_count(I,J) = NBR_HOLD_COUNT.  Call Link_Down(I,J).

7.7.  Optional Link Metrics

   Each node MAY maintain and update one or more link metrics for each
   link (I,J), representing the quality of the link, e.g., signal
   strength, number of HELLOs received over some time interval,
   reliability, stability, bandwidth, etc.  Each node MUST declare a
   neighbor to be LOST if either NBR_HOLD_COUNT HELLOs are missed or if
   no HELLO is received within NBR_HOLD_TIME seconds; however, a node
   MAY also declare a neighbor to be LOST based on a link metric being
   above or below some threshold.  Each node MUST receive at least
   HELLO_ACQUIRE_COUNT of the last HELLO_ACQUIRE_WINDOW HELLOs from a
   neighbor before declaring the neighbor 1-WAY or 2-WAY; however, a
   node MAY require an additional condition based on a link metric being
   above or below some threshold, before declaring the neighbor 1-WAY or
   2-WAY.  This document does not specify any particular link metric,
   but an implementation of TBRPF that uses such metrics is considered
   to be compliant with this specification.

   The function Link_Change(I,J) is called to alert the routing module
   whenever nbr_metric(I,J) changes significantly.  If the configurable
   parameter USE_METRICS is equal to 1, then the metrics nbr_metric(I,J)
   are used by the routing module for route computation, as described in
   Section 8.







Ogier, et al.                 Experimental                     [Page 18]


RFC 3684                         TBRPF                     February 2004


7.8.  Configurable Parameters

   This section lists the parameters used by the neighbor discovery
   protocol, and their proposed default values.  All nodes MUST be
   configured to have the same value for all of the following
   parameters.

      Parameter Name          Default Value
      --------------          -------------
      HELLO_INTERVAL          1 second
      MAX_JITTER              0.1 second
      NBR_HOLD_TIME           3 seconds
      NBR_HOLD_COUNT          3
      HELLO_ACQUIRE_COUNT     2
      HELLO_ACQUIRE_WINDOW    3

8.  TBRPF Routing Module

   This section describes the TBRPF routing module, which performs
   topology discovery and route computation.

8.1.  Conceptual Data Structures

   In addition to the information required by the neighbor discovery
   protocol, each node running TBRPF maintains a topology table TT,
   which stores information for each known node and link in the network.
   Nodes are identified by their RIDs, i.e., node u is the node whose
   RID is u.  The following information is stored in the topology table
   at node i for each node u and link (u,v):

      T(u,v) - Equal to 1 if (u,v) is in node i's source tree T, and 0
      otherwise.  The previous source tree is also maintained as old_T.

      RN(u) - Equal to 1 if u is in node i's reported node set RN, and 0
      otherwise.  The previous reported node set is also maintained as
      old_RN.

      RT(u,v) - Equal to 1 if (u,v) is in node i's reported subtree RT,
      and 0 otherwise.  Since RT is defined as the set of links (u,v) in
      T such that u is in RN, this variable need not be maintained
      explicitly.

      TG(u,v) - Equal to 1 if (u,v) is in node i's topology graph TG,
      and 0 otherwise.

      N - The set of 2-way neighbors of node i.





Ogier, et al.                 Experimental                     [Page 19]


RFC 3684                         TBRPF                     February 2004


      r(u,v) - The list of neighbors that are reporting link (u,v) in
      their reported subtree RT.  The set of links (u,v) reported by
      neighbor j is denoted RT_j.

      r(u) - The list of neighbors that are reporting node u in their
      reported node set RN.

      p(u) - The current parent for node u, equal to the next node on
      the shortest path to u.

      pred(u) - The node that is the predecessor of node u in the source
      tree T.  Equal to NULL if node u is not reachable.

      pred(j,u) - The node that is the predecessor of node u in the
      subtree RT_j reported by neighbor j.

      d(u) - The length of the shortest path to node u.  If USE_METRICS
      = 0, d(u) is the number of hops to node u.

      reported(u,v) - Equal to 1 if link (u,v) in TG is reported by
      p(u), and 0 otherwise.

      tg_expire(u) - Expiration time for links (u,v) in TG.

      rt_expire(j,u) - Expiration time for links (u,v) in RT_j.

      nr_expire(u,v) - Expiration time for a link (u,v) in TG such that
      reported(u,v) = 0.  Such non-reported links can be used
      temporarily during rerouting.

      metric(j,u,v) - The metric for link (u,v) reported by neighbor j.

      metric(u,v) - The metric for link (u,v) in TG.  For a neighbor j,
      metric(i,j) is the minimum of nbr_metric(I,J) over all 2-WAY links
      (I,J) from i to j.

      cost(u,v) - The cost for link (u,v), equal to metric(u,v) if
      USE_METRICS = 1, and otherwise equal to 1.

      local_if(j) - The address of the preferred local interface for
      forwarding packets to neighbor j.

      nbr_if(j) - The address of the preferred interface of neighbor j.








Ogier, et al.                 Experimental                     [Page 20]


RFC 3684                         TBRPF                     February 2004


   The routing table consists of a list of tuples of the form (rt_dest,
   rt_next, rt_dist, rt_if_id), where rt_dest is the destination IP
   address or prefix, rt_next is the interface address of the next hop
   of the route, rt_dist is the length of the route, and rt_if_id is the
   ID of the local interface through which the next hop can be reached.

   Each node also maintains three tables that describe associated IP
   addresses or prefixes:  the "interface table", which associates
   interface IP addresses with router IDs, the "host table", which
   associates host IP addresses with router IDs, and the "network prefix
   table", which associates network prefixes with router IDs.

   The "interface table" consists of tuples of the form (if_addr,
   if_rid, if_expire), where if_addr is an interface IP address
   associated with the router with RID = if_rid, and if_expire is the
   time at which the tuple expires and MUST be removed.  The interface
   table at a node does NOT contain an entry in which if_addr equals the
   node's own RID; thus, a node does not advertise its own RID as an
   associated interface.

   The "host table" consists of tuples of the form (h_addr, h_rid,
   h_expire), where h_addr is a host IP address associated with the
   router with RID = h_rid, and h_expire is the time at which the tuple
   expires and MUST be removed.

   The "network prefix table" consists of tuples of the form
   (net_prefix, net_length, net_rid, net_expire), where net_prefix and
   net_length describe a network prefix associated with the router with
   RID = net_rid, and net_expire is the time at which the tuple expires
   and MUST be removed.  A MANET may be configured as a "stub" network,
   in which case one or more gateway routers may announce a default
   prefix such that net_prefix = net_length = 0.  Two copies of each
   table are kept:  an "old" copy that was last reported to neighbors,
   and the current copy that is updated when association messages are
   received.

8.2.  TOPOLOGY UPDATE Message Format

   The TOPOLOGY UPDATE message has the two formats, depending on the
   size of the message.  The normal format is as follows, and is used
   whenever n, NRL, and NRNL all do not exceed 255:










Ogier, et al.                 Experimental                     [Page 21]


RFC 3684                         TBRPF                     February 2004


   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |M|D|0|0|  TYPE |       n       |     NRL       |    NRNL       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                      Router ID of u                           |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                      Router ID of v_1                         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   ~                              ...                              ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                      Router ID of v_n                         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     metric 1    |  metric 2   |            ...                |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                              ...                              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The message body contains the n+1 router IDs for nodes u,
   v_1,...,v_n, which represent the links (u,v_1),..., (u,v_n).  The
   first NRL of the v_k are reported leaf nodes, the next NRNL of the
   v_k are reported non-leaf nodes, and the last n - (NRL+NRNL) of the
   v_k are not reported (not in RN).

   The M bit indicates whether or not link metrics are included in the
   message.  If M = 1, then a 1-octet metric is included for each of the
   links (u,v_1),..., (u,v_n), following the last router ID.

   The D bit indicates whether or not implicit deletion is used, and
   must be set to 1 if and only if IMPLICIT_DELETION = 1.

   The TOPOLOGY UPDATE message has the following three subtypes:

   FULL (TYPE = 5)
      A FULL update (FULL, n, NRL, NRNL, u, v_1,..., v_n) reports that
      the links (u,v_1),..., (u,v_n) belong to the sending router's
      reported subtree RT, and that RT contains no other links with tail
      u.

   ADD (TYPE = 6)
      An ADD update (ADD, n, NRL, NRNL, u, v_1,..., v_n) reports that
      the links (u,v_1),..., (u,v_n) have been added to the sending
      router's reported subtree RT.

   DELETE (TYPE = 7)
      A DELETE update (DELETE, n, NRL, NRNL, u, v_1,..., v_n) reports
      that the links (u,v_1),..., (u,v_n) have been deleted from the
      sending router's reported subtree RT.





Ogier, et al.                 Experimental                     [Page 22]


RFC 3684                         TBRPF                     February 2004


   If n, NRL, or NRNL is larger than 255, then the long format of the
   TOPOLOGY UPDATE message is used, in which the first 4 octets of the
   normal format are replaced by the following 8 octets:

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |M|D|1|0|  TYPE |      0        |             n                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |            NRL                |            NRNL               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

8.3.  Interface, Host, and Network Prefix Association Message Formats

   The INTERFACE ASSOCIATION (TYPE = 8) and HOST ASSOCIATION (TYPE = 9)
   messages have the following format:

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |ST | 0 |  TYPE |    Reserved   |             n                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         Router ID                             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         IP Address                            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         IP Address                            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                              ...                              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The message body contains the router ID of the originating node, and
   n IP addresses of interfaces (TYPE = 8) or hosts (TYPE = 9) that are
   associated with the router ID.  The ST field is defined below.

   The NETWORK PREFIX ASSOCIATION message (TYPE = 10) has the following
   format:

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |ST | 0 |  TYPE |    Reserved   |             n                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         Router ID                             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | PrefixLength  | Prefix byte 1 | Prefix byte 2 |     ...       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |      ...      | PrefixLength  | Prefix byte 1 | Prefix byte 2 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |      ...                                                      |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+






Ogier, et al.                 Experimental                     [Page 23]


RFC 3684                         TBRPF                     February 2004


   The message body contains the router ID of the originating node, and
   n network prefixes, each specified by a 1-octet prefix length
   followed immediately by the prefix, using the minimum number of whole
   octets required.  To minimize overhead, the prefix lengths and
   prefixes are NOT aligned along word boundaries.

   The INTERFACE ASSOCIATION, HOST ASSOCIATION, and NETWORK PREFIX
   ASSOCIATION messages each have the following three subtypes (similar
   to those for the TOPOLOGY UPDATE message):

   FULL (ST = 0)
      Indicates that this is a FULL update that includes all interface
      addresses, host addresses, or network prefixes associated with the
      given router ID.

   ADD (ST = 1)
      Indicates that the included IP addresses or network prefixes are
      associated with the router ID, but may not include all such IP
      addresses or network prefixes.

   DELETE (ST = 2)
      Indicates that the included IP addresses or network prefixes are
      no longer associated with the router ID.

8.4.  TBRPF Routing Operation

   This section describes the operation of the TBRPF routing module.
   The operation is divided into the following subsections: periodic
   processing, updating the source tree and topology graph, updating the
   routing table, updating the reported node set, generating periodic
   updates, generating differential updates, processing topology
   updates, expiring topology information, optional reporting of
   redundant topology information, local topology changes, generating
   association messages, processing association messages, and non-relay
   operation.  The operation is described in terms of procedures (e.g.,
   Update_All), which may be executed periodically or in response to
   some event, and may be called by other procedures.  In all
   procedures, node i is the node executing the procedure.

8.4.1.  Periodic Processing

   Each node executes the procedure Update_All() periodically, at least
   once every DIFF_UPDATE_INTERVAL seconds, which is typically equal to
   HELLO_INTERVAL.  This procedure is defined as follows:







Ogier, et al.                 Experimental                     [Page 24]


RFC 3684                         TBRPF                     February 2004


Update_All()
  1. For each interface I, create empty message list msg_list(I).
  2. For each interface I, generate a HELLO message for
     interface I and add it to msg_list(I).
  3. Expire_Links().
  4. Update_Source_Tree().
  5. Update_Routing_Table().
  6. If REPORT_FULL_TREE = 0, execute Update_RN(); otherwise (the
     full source tree is reported) Update_RN_Simple().
  7. If current_time >= next_periodic:
     7.1. Generate_Periodic_Update().
     7.2. Set next_periodic = current_time + PER_UPDATE_INTERVAL.
  8. Else, Generate_Diff_Update().
  9. Generate_Association_Messages().
 10. For each interface I, send the msg_list(I) on interface I.
 11. Set old_T = T and old_RN = RN.

8.4.2.  Updating the Source Tree and Topology Graph

   The procedure Update_Source_Tree() is a variant of Dijkstra's
   algorithm, which is called periodically and in response to topology
   changes, to update the source tree T and the topology graph TG.  This
   algorithm computes shortest paths subject to two link cost penalties.
   The penalty NON_REPORT_PENALTY is added to the cost of links (u,v)
   that are not currently reported by the parent p(u) so that, whenever
   possible, a link (u,v) is included in T only if it is currently
   reported by the parent.  To allow immediate rerouting when p(u)
   changes, it may be necessary to temporarily use a link (u,v) that is
   not currently reported by the new parent.  The penalty
   NON_TREE_PENALTY is added to the cost of links (u,v) that are not
   currently in T, to reduce the number of changes to T.  When there
   exist multiple paths of equal cost to a given node, router ID is used
   to break ties.

   The algorithm is defined as follows (where node i is the node
   executing the procedure):

Update_Source_Tree()
  1. For each node v in TT, set d(v) = INFINITY, pred(v) = NULL,
     old_p(v) = p(v), and p(v) = NULL.

  2. Set d(i) = 0, p(i) = i, pred(i) = i.

  3. Set S = {i}. (S is the set of labeled nodes.)

  4. For each node j in N, set d(j) = c(i,j), pred(j) = i,
     and p(j) = j.  (If USE_METRICS = 0, then all link costs
     c(i,j) are 1.)



Ogier, et al.                 Experimental                     [Page 25]


RFC 3684                         TBRPF                     February 2004


  5. While there exists an unlabeled node u in TT such that
     d(u) < INFINITY:
     5.1. Let u be an unlabeled node in TT with minimum d(u).
          (A heap should be used to find u efficiently.)
     5.2. Add u to S (u becomes labeled).
     5.3. If p(u) is not equal to old_p(u) (parent has changed):
        5.3.1. For each link (u,v) in TG with tail u, if
               reported(u,v) = 1, set reported(u,v) = 0 and set
               nr_expire(u,v) = current_time + PER_UPDATE_INTERVAL.
        5.3.2. If p(u) is in r(u) (p(u) is reporting u):
           5.3.2.1. Set tg_expire(u) = rt_expire(p(u),u).
           5.3.2.2. If p(u) = u (u is a neighbor), remove all links
                    (u,v) with tail u from TG.
           5.3.2.3. For each link (u,v) with p(u) in r(u,v):
              5.3.2.3.1. Add (u,v) to TG and set reported(u,v) = 1.
              5.3.2.3.2. Set metric(u,v) = metric(p(u),u,v).
                         If USE_METRICS=1, set c(u,v)=metric(u,v).
     5.4. For each node v such that (u,v) is in TG:
        5.4.1. If reported(u,v) = 0,
               set cost = c(u,v) + NON_REPORT_PENALTY.
               (This penalizes (u,v) if not reported by p(u).)
        5.4.2. Else, if p(u) = u AND u is not in r(v),
               set cost = c(u,v) + NON_REPORT_PENALTY.
               (This penalizes (u,v) if u is a neighbor and is not
               reporting v.)
        5.4.3. If (u,v) is not in old_T and p(u) != u,
               set cost = cost + NON_TREE_PENALTY.
        5.4.4. If (d(u) + cost, u) is lexicographically less
               than (d(v), pred(v)), set d(v) = d(u) + c(u,v),
               pred(v) = u, and p(v) = p(u).

  6. Update the source tree T as follows:
     6.1. Remove all links from T.
     6.2. For each node u other than i such that pred(u) is not
          NULL, add the link (pred(u), u) to T.

8.4.3.  Updating the Routing Table

   The routing table is updated following any change to the source tree
   or the association tables (interface table, host table, or network
   prefix table).  The routing table is updated according to procedure
   Update_Routing_Table(), which is defined as follows:

Update_Routing_Table()

  1. Remove all tuples from the routing table.





Ogier, et al.                 Experimental                     [Page 26]


RFC 3684                         TBRPF                     February 2004


  2. For each node u in TT (other than this node) such that p(u) is
     not NULL, add the tuple (rt_dest, rt_next, rt_dist, rt_if_id)
     to the routing table, where:
        rt_dest = u,
        rt_if_id = local_if(p(u)),
        rt_next = nbr_if(p(u)),
        rt_dist = d(u).

  3. For each tuple (if_addr, if_rid, if_expire) in the interface
     table, if a routing table entry (rt_dest, rt_next, rt_dist,
     rt_if_id) exists such that rt_dest = if_rid, add the tuple
     (if_addr, rt_next, rt_dist, rt_if_id) to the routing table.

  4. For each tuple (h_addr, h_rid, h_expire) in the host table, if
     there exists a routing table entry (rt_dest, rt_next, rt_dist,
     rt_if_id) such that rt_dest = h_rid, add the tuple (h_addr,
     rt_next, rt_dist, rt_if_id) to the routing table, unless an
     entry already exists with the same value for h_addr and a
     lexicographically smaller value for (rt_dist, rt_dest).

  5. For each tuple (net_prefix, net_length, net_rid, net_expire)
     in the network prefix table, if there exists a routing table
     entry (rt_dest, rt_next, rt_dist, rt_if_id) such that
     rt_dest = net_rid, add the tuple (net_prefix/net_length,
     rt_next, rt_dist, rt_if_id) to the routing table, unless an
     entry already exists with the same value for
     net_prefix/net_length and a lexicographically smaller value
     for (rt_dist, rt_dest).

8.4.4.  Updating the Reported Node Set

   Recall that the reported subtree RT is defined to be the set of links
   (u,v) in T such that u is in the reported node set RN.  Each node
   updates its RN immediately before generating periodic or differential
   topology updates.

   If REPORT_FULL_TREE = 1 (so that a node reports its entire source
   tree), then RN simply consists of all reachable nodes, i.e., all
   nodes u such that pred(u) is not NULL.  The procedure that computes
   RN in this manner is called Update_RN_Simple().  The rest of this
   section describes how RN is computed assuming REPORT_FULL_TREE = 0.

   A node first determines which of its neighbors belong to RN.  Node i
   includes a neighbor j in RN if and only if node i determines that one
   of its neighbors may select i to be its next hop on its shortest path
   to j.  To make this determination, node i computes the shortest
   paths, up to 2 hops, from each neighbor to each other neighbor, using
   only neighbors (or node i itself) as an intermediate node, and using



Ogier, et al.                 Experimental                     [Page 27]


RFC 3684                         TBRPF                     February 2004


   relay priority and router ID to break ties.  If a link metric is
   used, then shortest paths are computed with respect to the link
   metric; otherwise min-hop paths are computed.

   After a node determines which neighbors are in RN, each node u (other
   than node i) in the topology table is included in RN if and only if
   the next hop p(u) to u is in RN.  Equivalently, node u is included in
   RN if and only if u is in the subtree of T rooted at some neighbor j
   that is in RN.  Thus, the reported subtree RT includes the subtrees
   of T that are rooted at neighbors in RN.  Node i also includes itself
   in RN; thus RT also includes all local links (i,j) to neighbors j.

   The precise procedure for updating RN is defined as follows:

Update_RN()
  1. Set RN = empty.
  2. For each neighbor s in N such that s is in r(s), i.e.,
     such that s is reporting itself:
     (Initialize to run Dijkstra for source s, for 2 hops.)
     2.1. For each node j in N+{i}, set dist(j) = INFINITY and
          par(j) = NULL.
     2.2. Set dist(s) = 0 and par(s) = s.
     2.3. For each node j in N+{i} such that (s,j) is in TG:
        2.3.1. Set dist(j) = metric(s,j), par(j) = j.
        2.3.2. For each node k in N such that (j,k) is in TG:
             2.3.2.1. Set cost = metric(j,k).
             2.3.2.2. If (dist(j) + cost, nbr_pri(j), j)
                is lexicographically less than
                (dist(k), nbr_pri(par(k)), par(k)),
                set dist(k) = dist(j) + cost and par(k) = j.
     2.4. For each neighbor j in N, add j to RN if par(j) = i.
  3. Add i to RN. (Node i is always in RN.)
  4. For each node u in the topology table, add u to RN if p(u)
     is in RN.

   In some cases it may be desirable to limit the radius (number of
   hops) that topology information is propagated.  Since each TBRPF
   packet is sent only to immediate (1-hop) neighbors, this cannot be
   achieved by using a time-to-live field.  Instead, the propagation of
   topology information can be limited to a radius of K hops by limiting
   RN (at all nodes) to include only nodes that are at most K-1 hops
   away.  Assuming min-hop routing is used, so that d(u) is the number
   of hops to node u, this can be done by modifying Step 4 of
   Update_RN() as follows:

  4. For each node u in the topology table, add u to RN if p(u)
     is in RN and d(u) <= K-1.




Ogier, et al.                 Experimental                     [Page 28]


RFC 3684                         TBRPF                     February 2004


8.4.5.  Generating Periodic Updates

   Every PER_UPDATE_INTERVAL seconds, each node generates and transmits,
   on all interfaces, a set of FULL TOPOLOGY UPDATE messages (one
   message for each node in RN that is not a leaf of T), which describes
   the reported subtree RT.  Whenever possible, these messages are
   included in a single packet, in order to minimize the number of
   control packets transmitted.

   Each topology update message contains the router IDs for n+1 nodes u,
   v_1,...,v_n, which represent the n links (u,v_1),..., (u,v_n).  The n
   head nodes v_1,..., v_n are divided into three lists in order to
   convey additional information and thus reduce the number of messages
   that must be generated.  In particular, the first NRL head nodes are
   leaves of T, thus avoiding the need to generate separate topology
   update messages for leaf nodes u.  Similarly, the last n-(NRL+NRNL)
   head nodes are not in RN, thus avoiding the need to generate separate
   topology update messages for nodes u that have been removed from RN.

   Periodic update messages are generated according to procedure
   Generate_Periodic_Update(), defined as follows (where node i is the
   node executing the procedure):

   Generate_Periodic_Update()
     For each node u in RN (including node i) that is not a leaf of T,
     add the update (FULL, n, NRL, NRNL, u, v_1,..., v_n)
     to msg_list(I) for each interface I, where:

     (a) v_1,..., v_n are the nodes v such that (u,v) is in T,
         the first NRL of these are nodes in RN that are leaves of T,
         the next NRNL of these are nodes in RN that are not leaves
         of T, and the last n-(NRL+NRNL) of these are not in RN.

     (b) If USE_METRICS = 1, then the M (metrics) bit is set to 1 and
         the link metrics metric(u,v_1),..., metric(u,v_n) are
         included in the message.

8.4.6.  Generating Differential Updates

   Every DIFF_UPDATE_INTERVAL seconds, if it is not time to generate a
   periodic update, and if RT has changed since the last time a topology
   update was generated, a set of TOPOLOGY UPDATE messages describing
   the changes to RT is generated and transmitted on all interfaces.
   These messages are constructed according to procedure
   Generate_Differential_Update(), defined as follows:






Ogier, et al.                 Experimental                     [Page 29]


RFC 3684                         TBRPF                     February 2004


Generate_Differential_Update()
  For each node u in RN:
  1. If u is not in old_RN (u was added to RN) and is not a leaf
     of T, add the update (FULL, n, NRL, NRNL, u, v_1,..., v_n)
     to msg_list(I) for each I, where:
     (a) v_1,..., v_n, NRL, and NRNL are defined as above for
         periodic updates.
     (b) If USE_METRICS = 1, then the M (metrics) bit is set to 1
         and the link metrics metric(u,v_1),..., metric(u,v_n)
         are included in the message.

  2. Else, if u is in old_RN and is not a leaf of T:
     2.1. Let v_1,..., v_n be the nodes v such that (u,v) is in T
          AND at least one of the following 3 conditions holds:
              (a) (u,v) is not in old_T, or
              (b) v is in old_RN but not in RN, or
              (c) v is a leaf and is in RN but not in old_RN.
     2.2. If this set of nodes is nonempty, add the update
          (ADD, n, NRL, NRNL, u, v_1,..., v_n) to msg_list(I) for
          each interface I, where:
          (a) NRL and NRNL are defined as above.
          (b) If USE_METRICS = 1, then the M (metrics) bit is
              set to 1 and the link metrics metric(u,v_1),...,
              metric(u,v_n) are included in the message.

  3. If u is in old_RN:
     3.1. Let v_1,..., v_n be the nodes v such that (u,v) is in
          old_T but not in TG, and either IMPLICIT_DELETION = 0
          or pred(v) is not in RN (or is NULL).
          (If IMPLICIT_DELETION = 1 and pred(v) is in RN, then
          the deletion of (u,v) is implied by an ADD update for
          another link (w,v).)
      3.2. If this set of nodes is nonempty, add the update
         (DELETE, n, u, v_1,..., v_n) to msg_list(I) for each I.

8.4.7.  Processing Topology Updates

   When a packet containing a list (msg_list) of TOPOLOGY UPDATE
   messages is received from node j, the list is processed according to
   the procedure Process_Updates(j, msg_list), defined as follows.  In
   particular, this procedure updates TT, TG, and the reporting neighbor
   lists r(u) and r(u,v).  If any link in T has been deleted from TG,
   then Update_Source_Tree() and Update_Routing_Table() are called to
   provide immediate rerouting.

Process_Updates(j, msg_list)
  1. For each update = (subtype, n, NRL, NRNL, u, v_1,..., v_n)
     in msg_list:



Ogier, et al.                 Experimental                     [Page 30]


RFC 3684                         TBRPF                     February 2004


     1.1. Create an entry for u in TT if it does not exist.
     1.2. If subtype = FULL, Process_Full_Update(j, update).
     1.3. If subtype = ADD, Process_Add_Update(j, update).
     1.4. If subtype = DELETE, Process_Delete_Update(j, update).
  2. If there exists any link in T that is not in TG:
     2.1. Update_Source_Tree().
     2.2. Update_Routing_Table().

Process_Full_Update(j, update)
  1. Add j to r(u).
  2. Set rt_expire(j,u) = current_time + TOP_HOLD_TIME.
  3. For each link (u,v) s.t. j is in r(u,v):
     3.1. Remove j from r(u,v).
     3.2. If pred(j,v) = u, set pred(j,v) = NULL.
  4. If j = p(u) OR p(u) = NULL:
     4.1. Set tg_expire(u) = current_time + TOP_HOLD_TIME.
     4.2. For each v s.t. (u,v) is in TG,
          If reported(u,v) = 1, remove (u,v) from TG.
  5. Process_Add_Update(j, update).

Process_Add_Update(j, update)
  For m = 1,..., n:
     ((u,v_m) is the mth link in update.)
     1. Let v = v_m.
     2. Create an entry for v in TT if it does not exist.
     3. Add j to r(u,v).
     4. If j = p(u) OR p(u) = NULL:
        4.1. Add (u,v) to TG.
        4.2. Set reported(u,v) = 1.
     5. If the M (metrics) bit in update is 1:
        5.1. Set metric(j,u,v) to the m-th metric in the update.
        5.2. If j = p(u) OR p(u) = NULL:
           5.2.1. Set metric(u,v) = metric(j,u,v).
           5.2.2. If USE_METRICS = 1, set c(u,v) = metric(u,v).
     6. If the D (implicit deletion) bit in update is 1:
        6.1. Set w = pred(j,v).
        6.2. If (w != NULL AND w != u):
           6.2.1. Remove j from r(w,v).
           6.2.2. If j = p(w), remove (w,v) from TG.
     7. Set pred(j,v) = u.  (Set new predecessor.)
     8. If m <= NRL (v = v_m is a reported leaf):
        8.1. Set leaf_update = (FULL, 0, 0, 0, v).
        8.2. Process_Full_Update(j, leaf_update).
     9. If m > NRL + NRNL (v = v_m is not reported by j):
        9.1. Remove j from r(v).
        9.2. Set rt_expire(j,v) = 0.
        9.3. For each node w s.t. j is in r(v,w),
             remove j from r(v,w).



Ogier, et al.                 Experimental                     [Page 31]


RFC 3684                         TBRPF                     February 2004


        9.4. If j = p(v), then for each node w s.t. (v,w) is in TG
               and reported(v,w) = 1, set reported(v,w) = 0 and set
               nr_expire(v,w) = current_time + PER_UPDATE_INTERVAL.

Process_Delete_Update(j, update)
  For m = 1,..., n:
     ((u,v_m) is the mth link in update.)
     1. Let v = v_m.
     2. Remove j from r(u,v).
     3. If pred(j,v) = u, set pred(j,v) = NULL.
     4. If j = p(u), remove (u,v) from TG.

8.4.8.  Expiring Topology Information

   Each node periodically checks for outdated topology information based
   on the expiration timers tg_expire(u), rt_expire(j,u), and
   nr_expire(u,v), and removes any expired entries from TG and from the
   lists r(u) and r(u,v).  This is done according to the following
   procedure Expire_Links(), which is called periodically just before
   the source tree is updated.

Expire_Links()
  For each node u in TT other than node i:
     1. If tg_expire(u) < current_time, then for each v s.t.
        (u,v) is in TG, remove (u,v) from TG.
     2. Else, for each v s.t. (u,v) is in TG,
        if reported(u,v) = 0 AND nr_expire(u,v) < current_time,
        remove (u,v) from TG.
     3. For each node j in r(u), if rt_expire(j,u) < current_time:
        3.1. Remove j from r(u).
        3.2. For each link (u,v) s.t. j is in r(u,v),
             remove j from r(u,v).

   In addition, the following cleanup steps SHOULD be executed
   periodically to remove unnecessary entries from the topology table
   TT.  A link (u,v) should be removed from TT if it is not in TG and
   not in old_T.  A node u should be removed from TT if all of the
   following conditions hold: r(u) is empty, r(w,u) is empty for all w,
   and no link of TG has u as either the head or the tail.

8.4.9.  Optional Reporting of Redundant Topology Information

   Each node is required to report its reported subtree RT to neighbors.
   However, each node (independently of the other nodes) MAY report
   additional links, e.g., to provide increased robustness in highly
   mobile networks.  For example, a node may compute any subgraph H of
   TG that contains T, and may report the "reported subgraph" RH which
   consists of links (u,v) of H such that u is in RN.  In this case,



Ogier, et al.                 Experimental                     [Page 32]


RFC 3684                         TBRPF                     February 2004


   each periodic update describes RH instead of RT, and each
   differential update describes changes to RH.  If this option is used,
   then the parameter IMPLICIT_DELETION MUST be set to 0, since the
   deletion of a link cannot be implied by the addition of another link
   if redundant topology information is reported.

8.4.10.  Local Topology Changes

   This section describes the procedures that are followed when the
   neighbor discovery module detects a new link, the loss of a link, or
   a change in the metric for a link.

   When a link (I,J) from a local interface I to a neighbor interface J
   is discovered via the neighbor discovery module, the procedure
   Link_Up(I,J) is executed, as defined below.  Letting j be the
   neighbor node associated with interface J, Link_Up(I,J) adds j to N
   (if it does not already belong), updates the preferred local
   interface local_if(j) and neighbor interface nbr_if(j) so that the
   link from local_if(j) to nbr_if(j) has the minimum metric among all
   links from i to j, and updates metric(i,j) to be this minimum metric.

Link_Up(I,J)
   1. Let j = nbr_rid(I,J).
   2. If j is not in N:
      2.1. Add j to N.
      2.2. Add (i,j) to TG.
      2.3. Set reported(i,j) = 1.
   3. If nbr_metric(I,J) < metric(i,j), set local_if(j) = I,
      nbr_if(j) = J, and metric(i,j) = nbr_metric(I,J).
   4. If USE_METRICS = 1, set cost(i,j) = metric(i,j).

   When the loss of a link (I,J) from a local interface I to a neighbor
   interface J is detected via the neighbor discovery module, the
   procedure Link_Down(I,J) is executed, as defined below.  Note that
   routes are updated immediately when a link is lost, and if the lost
   link is due to a link-layer failure notification, a differential
   topology update is sent immediately.

Link_Down(I,J)
   1. Let j = nbr_rid(I,J).
   2. If there does not exist a link (K,L) from node i to
      node j with nbr_status(K,L) = 2-WAY:
      2.1. Remove j from N.
      2.2. Remove (i,j) from TG.
   3. If j is in N:
      3.1. Let (K,L) be a link from i to j such that
           nbr_metric(K,L) is the minimum metric among
           all links from i to j.



Ogier, et al.                 Experimental                     [Page 33]


RFC 3684                         TBRPF                     February 2004


      3.2. Set local_if(j) = K, nbr_if(j) = L, and
           metric(i,j) = nbr_metric(K,L).
      3.3. If USE_METRICS = 1, set cost(i,j) = metric(i,j).
   5. Update_Source_Tree().
   6. Update_Routing_Table().
   7. If j is not in N and lost link is due to link-layer failure
      notification:
      7.1. If (REPORT_FULL_TREE = 0) Update_RN().
      7.2. Else, Update_RN_Simple().
      7.3. Set msg_list = empty.
      7.4. Generate_Diff_Update().
      7.5. Send msg_list on all interfaces.
      7.6. Set old_T = T and old_RN = RN.

   If the metric of a link (I,J) from a local interface I to a neighbor
   interface J changes via the neighbor discovery module, the following
   procedure Link_Change(I,J) is executed.

Link_Change(I,J)
   1. Let j = nbr_rid(I,J).
   2. Let (K,L) be a link from i to j such that
      nbr_metric(K,L) is the minimum metric among
      all links from i to j.
   3. Set local_if(j) = K, nbr_if(j) = L, and
      metric(i,j) = nbr_metric(K,L).
   4. If USE_METRICS = 1, set cost(i,j) = metric(i,j).

8.4.11.  Generating Association Messages

   This section describes the procedures used to generate INTERFACE
   ASSOCIATION, HOST ASSOCIATION, and NETWORK PREFIX ASSOCIATION
   messages.  Addresses or prefixes in the interface table, host table,
   and network prefix table are reported to neighbors periodically every
   IA_INTERVAL, HA_INTERVAL, and NPA_INTERVAL seconds, respectively.  In
   addition, differential changes to the tables are reported every
   DIFF_UPDATE_INTERVAL seconds if it is not time for a periodic update
   (similar to differential topology updates).  Each node reports only
   addresses or prefixes that are associated with nodes in the reported
   node set RN; this ensures the efficient broadcast of all associated
   addresses and prefixes to all nodes in the network.

   The generated messages are sent on each interface.  Whenever
   possible, these messages are combined into the same packet, in order
   to minimize the number of control packets transmitted.

Generate_Association_Messages()
   1. Generate_Interface_Association_Messages().
   2. Generate_Host_Association_Messages().



Ogier, et al.                 Experimental                     [Page 34]


RFC 3684                         TBRPF                     February 2004


   3. Generate_Network_Prefix_Association_Messages().

Generate_Interface_Association_Messages()
   1. If current_time > next_ia_time:
      1.1. Set next_ia_time = current_time + IA_INTERVAL.
      1.2. For each node u in RN:
         1.2.1. Let addr_1,..., addr_n be the interface IP
            addresses associated with RID u in the current
            interface table.
         1.2.2. If this list is nonempty, add the INTERFACE
            ASSOCIATION message (FULL, n, u, addr_1,..., addr_n)
            to msg_list(I) for each I.

   2. Else, for each node u in RN:
      2.1. Add the INTERFACE ASSOCIATION message (ADD, n, u,
         addr_1,..., addr_n) to msg_list(I) for each I, where
         addr_1,..., addr_n are the interface IP addresses that
         are associated with RID u in the current interface table
         but not in the old interface table.
      2.2. Add the INTERFACE ASSOCIATION message (DELETE, n, u,
         addr_1,..., addr_n) to msg_list(I) for each I, where
         addr_1,..., addr_n are the interface IP addresses that
         are associated with RID u in the old interface table
         but not in the current interface table.

Generate_Host_Association_Messages()
   1. If current_time > next_ha_time:
      1.1. Set next_ha_time = current_time + HA_INTERVAL.
      1.2. For each node u in RN:
         1.2.1. Let addr_1,..., addr_n be the host IP addresses
            associated with RID u in the current host table.
         1.2.2. If this list is nonempty, add the HOST ASSOCIATION
            message (FULL, n, u, addr_1,..., addr_n) to
            msg_list(I) for each I.

   2. Else, for each node u in RN:
      2.1. Add the HOST ASSOCIATION message (ADD, n, u,
         addr_1,..., addr_n) to msg_list(I) for each I, where
         addr_1,..., addr_n are the host IP addresses that
         are associated with RID u in the current host table
         but not in the old host table.
      2.2. Add the HOST ASSOCIATION message (DELETE, n, u,
         addr_1,..., addr_n) to msg_list(I) for each I, where
         addr_1,..., addr_n are the host IP addresses that
         are associated with RID u in the old host table
         but not in the current host table.





Ogier, et al.                 Experimental                     [Page 35]


RFC 3684                         TBRPF                     February 2004


Generate_Network_Prefix_Association_Messages()
   1. If current_time > next_npa_time:
      1.1. Set next_npa_time = current_time + NPA_INTERVAL.
      1.2. For each node u in RN:
         1.2.1. Let length_1, prefix_1,..., length_n, prefix_n
            be the network prefix lengths and prefixes associated
            with RID u in the current network prefix table.
         1.2.2. If this list is nonempty, add the NETWORK PREFIX
            ASSOCIATION message (FULL, n, u, length_1, prefix_1,
            ..., length_n, prefix_n) to msg_list(I) for each I.

   2. Else, for each node u in RN:
      2.1. Add the NETWORK PREFIX ASSOCIATION message
         (ADD, n, u, prefix_1,..., prefix_n) to msg_list(I) for
         each I, where prefix_1,..., prefix_n are the network
         prefixes that are associated with RID u in the current
         prefix table but not in the old prefix table.

      2.1. Add the NETWORK PREFIX ASSOCIATION message
         (DELETE, n, u, prefix_1,..., prefix_n) to msg_list(I) for
         each I, where prefix_1,..., prefix_n are the network
         prefixes that are associated with RID u in the old prefix
         table but not in the current prefix table.

8.4.12.  Processing Association Messages

   When an INTERFACE ASSOCIATION, HOST ASSOCIATION, or NETWORK PREFIX
   ASSOCIATION message is received from node j, the interface table,
   host table, or network prefix table, respectively, is updated as
   described in the following three procedures.

Process_Interface_Association_Messages(j, msg_list)
  For each message (subtype, n, u, addr_1,..., addr_n) in msg_list
  such that j = p(u):
     1. If subtype = FULL, remove all entries with if_rid = u
        from the interface table.
     2. If subtype = FULL or ADD, then for m = 1,..., n,
        add the tuple (if_addr, if_rid, if_expire) to the
        interface table, where:
           if_addr = addr_m,
           if_rid = u,
           if_expire = current_time + IA_HOLD_TIME.
     3. If subtype = DELETE, then for m = 1,..., n,
        remove the tuple (if_addr, if_rid, if_expire) from the
        interface table, where if_addr = addr_m and if_rid = u.






Ogier, et al.                 Experimental                     [Page 36]


RFC 3684                         TBRPF                     February 2004


Process_Host_Association_Messages(j, msg_list)
  For each message (subtype, n, u, addr_1,..., addr_n) in msg_list
  such that j = p(u):
     1. If subtype = FULL, remove all entries with h_rid = u
        from the host table.
     2. If subtype = FULL or ADD, then for m = 1,..., n,
        add the tuple (h_addr, h_rid, h_expire) to the
        host table, where:
           h_addr = addr_m,
           h_rid = u,
           h_expire = current_time + HA_HOLD_TIME.
     3. If subtype = DELETE, then for m = 1,..., n,
        remove the tuple (h_addr, h_rid, h_expire) from the
        host table, where h_addr = addr_m and h_rid = u.

Process_Network_Prefix_Association_Messages(j, msg_list)
   For each message (subtype, n, u, length_1, prefix_1, ...,
   length_n, prefix_n) in msg_list such that j = p(u):
      1. If subtype = FULL, remove all entries with net_rid = u
         from the prefix table.
      2. If subtype = FULL or ADD, then for m = 1,..., n,
         add the tuple (net_prefix, net_length, net_rid,
         net_expire) to the network prefix table, where:
            net_prefix = prefix_m,
            net_length = length_m,
            net_rid = u,
            net_expire = current_time + NPA_HOLD_TIME.
      3. If subtype = DELETE, then for m = 1,..., n,
         remove the tuple (net_prefix, net_length, net_rid,
         net_expire) from the network prefix table, where
         net_prefix = prefix_m, net_length = length_m,
         and net_rid = u.

8.4.13.  Non-Relay Operation

   Nodes with relay priority equal to zero are called non-relay nodes,
   and do not forward packets (of any type) that are received from other
   nodes.  A non-relay node is implemented simply by not generating or
   transmitting any TOPOLOGY UPDATE messages.  A non-relay node may
   report (in association messages) addresses or prefixes that are
   associated with itself, but not those associated with other nodes.
   HELLO messages must be transmitted in order to establish links with
   neighbor nodes.  The following procedures can be omitted in non-relay
   nodes: Update_RN(), Generate_Periodic_Update(), and
   Generate_Diff_Update().






Ogier, et al.                 Experimental                     [Page 37]


RFC 3684                         TBRPF                     February 2004


8.5.  Configurable Parameters

   This section lists the configurable parameters used by the routing
   module, and their proposed default values.  All nodes MUST have the
   same value for all of the following parameters except
   REPORT_FULL_TREE and IMPLICIT_DELETION.

      Parameter Name          Default Value
      --------------          -------------
      DIFF_UPDATE_INTERVAL    1 second
      PER_UPDATE_INTERVAL     5 seconds
      TOP_HOLD_TIME           15 seconds
      NON_REPORT_PENALTY      1.01
      NON_TREE_PENALTY        0.01
      IA_INTERVAL             10 seconds
      IA_HOLD_TIME            3 * IA_INTERVAL
      HA_INTERVAL             10 seconds
      HA_HOLD_TIME            3 * HA_INTERVAL
      NPA_INTERVAL            10 seconds
      NPA_HOLD_TIME           3 * NPA_INTERVAL
      USE_METRICS             0
      REPORT_FULL_TREE        0
      IMPLICIT_DELETION       1

9.  TBRPF Flooding Mechanism

   This section describes a mechanism for the efficient best-effort
   flooding (or network-wide broadcast) of packets to all nodes of a
   connected ad-hoc network.  This mechanism can be considered an
   optimization of the classical flooding algorithm in which each packet
   is transmitted by every node of the network.  In TBRPF flooding,
   information provided by TBRPF is used to decide whether a given
   received flooded packet should be forwarded.  As a result, each
   packet is transmitted by only a relatively small subset of nodes,
   thus consuming much less bandwidth than classical flooding.

   This document specifies that the flooding mechanism use the IPv4
   multicast address 224.0.1.20 (currently assigned by IANA for "any
   private experiment").  Every node maintains a duplicate cache to keep
   track of which flooded packets have already been received.  The
   duplicate cache contains, for each received flooded packet, the
   flooded packet identifier (FPI), which for IPv4 is composed of the
   source IP address, the IP identification, and the fragment offset
   values obtained from the IP header [14].

   When a node receives a packet whose destination IP address is the
   flooding address (224.0.1.20), it checks its duplicate cache for an
   entry that matches the packet.  If such an entry exists, the node



Ogier, et al.                 Experimental                     [Page 38]


RFC 3684                         TBRPF                     February 2004


   silently discards the flooded packet since it has already been
   received.  Otherwise, the node retransmits the packet on all
   interfaces (see the exception below) if and only if the following
   conditions hold:

   1. The TBRPF node associated with the source IP address of the packet
      belongs to the set RN of reported nodes computed by TBRPF.

   2. When decremented, the 'ip_ttl' in the IPv4 packet header
      (respectively, the 'hop_count' in the IPv6 packet header) is
      greater than zero.

   If the packet is to be retransmitted, it is sent after a small random
   time interval in order to avoid collisions.  If the interface on
   which the packet was received is not a MANET interface (see the
   Terminology section), then the packet should not be retransmitted on
   that interface.

10.  Operation of TBRPF in Mobile Ad-Hoc Networks

   TBRPF is particularly well suited to MANETs consisting of mobile
   nodes with wireless network interfaces operating in peer-to-peer
   fashion over a multiple access communications channel.  Although
   applicable across a much broader field of use, TBRPF is particularly
   well suited for supporting the standard DARPA Internet protocols
   [3][2].  In the following sections, we discuss practical
   considerations for the operation of TBRPF on MANETs.

10.1.  Data Link Layer Assumptions

   We assume a MANET data link layer that supports broadcast, multicast
   and unicast addressing with best-effort (not guaranteed) delivery
   services between neighbors (i.e., a pair of nodes within operational
   communications range of one another).  We further assume that each
   interface belonging to a node in the MANET is assigned a unicast data
   link layer address that is unique within the MANET's scope.  While
   such uniqueness is not strictly guaranteed, the assumption of
   uniqueness is consistent with current practices for deployment of the
   Internet protocols on specific link layers.  Methods for duplicate
   link layer address detection and deconfliction are beyond the scope
   of this document.

10.2.  Network Layer Assumptions

   MANETs are formed as collections of routers and non-routing nodes
   that use network layer addresses when calculating the MANET topology.
   We assume that each node has at least one data link layer interface
   (described above) and that each such interface is assigned a network



Ogier, et al.                 Experimental                     [Page 39]


RFC 3684                         TBRPF                     February 2004


   layer address that is unique within the MANET.  (Methods for network
   layer address assignment and duplicate address detection are beyond
   the scope of this document.)  We further assume that each node will
   select a unique Router ID (RID) for use in TBRPF protocol messages,
   whether or not the node acts as a MANET router.  Finally, we assume
   that each MANET router supports the multi-hop relay paradigm at the
   network layer; i.e., each router provides an inter-node forwarding
   service via network layer host routes which reflect the current MANET
   topology as perceived by TBRPF.

10.3.  Optional Automatic Address Resolution

   TBRPF employs a proactive neighbor discovery protocol at the network
   layer that maintains bi-directional link state for neighboring nodes
   through the periodic transmission of messages.  Since TBRPF neighbor
   discovery messages contain both the data link and network layer
   address of the sender, implementations MAY perform automatic
   network-to-data link layer address resolution for the nodes with
   which they form links.  An implementation may use such a mechanism to
   avoid additional message overhead and potential for packet loss
   associated with on-demand address resolution mechanisms such as ARP
   [15] or IPv6 Neighbor Discovery [16].  Implementations MUST respond
   to on-demand address resolution requests in the normal manner.

10.4.  Support for Multiple Interfaces and/or Alias Addresses

   MANET nodes may comprise multiple interfaces; each with a unique
   network layer address.  Additionally, MANET nodes may wish to publish
   alias addresses such as when multiple network layer addresses are
   assigned to the same interface or when the MANET node is serving as a
   Mobile IP [17] home agent.  Multiple interfaces and alias addresses
   are advertised in INTERFACE ASSOCIATION messages, which bind each
   such address to the node's RID.

10.5.  Support for Network Prefixes

   MANET routers may advertise network prefixes which the router
   discovered via attached networks, external routes advertised by other
   protocols, or other means.  Network prefixes are advertised in
   NETWORK PREFIX ASSOCIATION messages, which bind each such prefix to
   the node's RID.

10.6.  Support for non-MANET Hosts

   Non-MANET hosts may establish connections to MANET routers through
   on-demand mechanisms such as ARP or IPv6 Neighbor Discovery.  Such
   connections do not constitute a MANET link and therefore are not
   reported in TBRPF topology updates.  Non-MANET hosts are advertised



Ogier, et al.                 Experimental                     [Page 40]


RFC 3684                         TBRPF                     February 2004


   in HOST ASSOCIATION messages, which bind the IP address of each host
   to the node's RID.

10.7.  Internet Protocol Considerations

   TBRPF packets are communicated using UDP/IP.  Port 712 has been
   assigned by IANA for exclusive use by TBRPF.  Implementations in
   private networks MAY employ alternate data delivery services (i.e.,
   raw IP or local data-link encapsulation).  The selection of an
   alternate data delivery service MUST be consistent among all MANET
   routers in the private network.  In all implementations, the data
   delivery service MUST provide a checksum facility.

   The following sections specify the operation of TBRPF over UDP/IP.

10.7.1.  IPv4 Operation

   When IPv4 is used, TBRPF nodes obey IPv4 host and router requirements
   [4][5].  TBRPF packets are sent to the multicast address 224.0.0.2
   (All Routers) and thus reach all TBRPF routers within single-hop
   transmission range of the sender.  TBRPF routers MUST NOT forward
   packets sent to this multicast address.

   Since non-negligible packet loss due to link failure, interference,
   etc. can occur, implementations SHOULD avoid IPv4 fragmentation/
   reassembly whenever possible, by splitting large TBRPF protocol
   packets into multiple smaller packets at the application layer.  When
   fragmentation is unavoidable, senders SHOULD NOT send TBRPF packets
   that exceed the minimum reassembly buffer size ([4], section 3.3.2)
   for all receivers in the network.

10.7.2.  IPv6 Operation

   The specification of TBRPF for IPv6 is the same as for IPv4, except
   that 32-bit IPv4 addresses are replaced by 128-bit IPv6 addresses.
   However, to minimize overhead, router IDs remain at 32 bits, similar
   to OSPF for IPv6 [18].

11.  IANA Considerations

   The IANA has assigned port number 712 for TBRPF.

   The TBRPF flooding mechanism specified in this document uses the IPv4
   multicast address 224.0.1.20, which is currently assigned by IANA for
   "any private experiment".  In the event that this specification is
   advanced to standards track, a new multicast address assignment would
   be requested for this purpose.




Ogier, et al.                 Experimental                     [Page 41]


RFC 3684                         TBRPF                     February 2004


12.  Security Considerations

   Wireless networks are vulnerable to a variety of attacks, including
   denial-of-service attacks (e.g., flooding and jamming), man-in-the-
   middle attacks (e.g., interception, insertion, deletion,
   modification, replaying) and service theft.  To counter such attacks,
   it is important to prevent the spoofing (impersonation) of TBRPF
   nodes, and to prevent unauthorized nodes from joining the network via
   neighbor discovery.  To achieve this, TBRPF packets can be
   authenticated using the IP Authentication Header [19][20].  In
   addition, the Encapsulating Security Payload (ESP) header [21] can be
   used to provide confidentiality (encryption) of TBRPF packets.

   The IETF SEcuring Neighbor Discovery (SEND) Working Group analyzes
   trust models and threats for ad hoc networks [22].  TBRPF can be
   extended in a straightforward manner to use SEND mechanisms, e.g.,
   [23].

13.  Acknowledgements

   The authors would like to thank the Army Systems Engineering Office
   (ASEO) for funding part of this work.

   The authors would like to thank several members of the MANET working
   group for many helpful comments and suggestions, including Thomas
   Clausen, Philippe Jacquet, and Joe Macker.

   The authors would like to thank Bhargav Bellur for major
   contributions to the original (full-topology) version of TBRPF,
   Ambatipudi Sastry for his support and advice, and Julie S. Wong for
   developing a new implementation of TBRPF and suggesting several
   clarifications to the TBRPF Routing Operation section.

14.  References

14.1.  Normative References

   [1]  Bradner, S., "Key words for use in RFCs to Indicate Requirement
        Levels", BCP 14, RFC 2119, March 1997.

   [2]  Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6)
        Specification", RFC 2460, December 1998.

   [3]  Postel, J., "Internet Protocol", STD 5, RFC 791, September 1981.

   [4]  Braden, R., Ed., "Requirements for Internet Hosts -
        Communication Layers", STD 3, RFC 1122, October 1989.




Ogier, et al.                 Experimental                     [Page 42]


RFC 3684                         TBRPF                     February 2004


   [5]  Baker, F., Ed., "Requirements for IP Version 4 Routers", RFC
        1812, June 1995.

14.2.  Informative References

   [6]  Moy, J., "OSPF Version 2", STD 54, RFC 2328, April 1998.

   [7]  Ogier, R., Message in IETF email archive for MANET,
        ftp://ftp.ietf.org/ietf-mail-archive/manet/2002-02.mail,
        February 2002.

   [8]  Ogier, R., "Topology Dissemination Based on Reverse-Path
        Forwarding (TBRPF): Correctness and Simulation Evaluation",
        Technical Report, SRI International, October 2003.

   [9]  Ogier, R., Message in IETF email archive for MANET,
        ftp://ftp.ietf.org/ietf-mail-archive/manet/2002-03.mail, March
        2002.

   [10] Ogier, R., "Efficient Routing Protocols for Packet-Radio
        Networks Based on Tree Sharing", Proc. Sixth IEEE Intl. Workshop
        on Mobile Multimedia Communications (MOMUC'99), November 1999.

   [11] Bellur, B. and R. Ogier, "A Reliable, Efficient Topology
        Broadcast Protocol for Dynamic Networks", Proc. IEEE INFOCOM
        '99, New York", March 1999.

   [12] Clausen, T. and P. Jacquet, Eds., "Optimized Link State Routing
        Protocol (OLSR)", RFC 3626, October 2003.

   [13] Bertsekas, D. and R. Gallager, "Data Networks", Prentice-Hall,
        1987.

   [14] Perkins, C., Belding-Royer, E. and S. Das, "IP Flooding in Ad
        Hoc Mobile Networks", Work in Progress, November 2001.

   [15] Plummer, D., "Ethernet Address Resolution Protocol: Or
        converting network protocol addresses to 48.bit Ethernet address
        for transmission on Ethernet hardware", STD 37, RFC 826,
        November 1982.

   [16] Narten, T., Nordmark, E. and W. Simpson, "Neighbor Discovery for
        IP Version 6 (IPv6)", RFC 2461, December 1998.

   [17] Perkins, C., Ed., "IP Mobility Support for IPv4", RFC 3344,
        August 2002.





Ogier, et al.                 Experimental                     [Page 43]


RFC 3684                         TBRPF                     February 2004


   [18] Coltun, R., Ferguson, D. and J. Moy, "OSPF for IPv6", RFC 2740,
        December 1999.

   [19] Kent, S. and R. Atkinson, "Security Architecture for the
        Internet Protocol", RFC 2401, November 1998.

   [20] Kent, S. and R. Atkinson, "IP Authentication Header", RFC 2402,
        November 1998.

   [21] Kent, S. and R. Atkinson, "IP Encapsulating Security Payload
        (ESP)", RFC 2406, November 1998.

   [22] Nikander, P., "IPv6 Neighbor Discovery Trust Models and
        Threats", Work in Progress, April 2003.

   [23] Arkko, J., "SEcure Neighbor Discovery (SEND)", Work in Progress,
        June 2003.


































Ogier, et al.                 Experimental                     [Page 44]


RFC 3684                         TBRPF                     February 2004


Authors' Addresses

   Richard G. Ogier
   SRI International
   333 Ravenswood Ave.
   Menlo Park, CA  94025
   USA

   Phone: +1 650 859-4216
   Fax:   +1 650 859-4812
   EMail: ogier@erg.sri.com


   Fred L. Templin
   Nokia
   313 Fairchild Drive
   Mountain View, CA  94043
   USA

   Phone: +1 650 625 2331
   Fax:   +1 650 625 2502
   EMail: ftemplin@iprg.nokia.com


   Mark G. Lewis
   SRI International
   333 Ravenswood Ave.
   Menlo Park, CA  94025
   USA

   Phone: +1 650 859-4302
   Fax:   +1 650 859-4812
   EMail: lewis@erg.sri.com


















Ogier, et al.                 Experimental                     [Page 45]


RFC 3684                         TBRPF                     February 2004


Full Copyright Statement

   Copyright (C) The Internet Society (2004).  This document is subject
   to the rights, licenses and restrictions contained in BCP 78 and
   except as set forth therein, the authors retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE
   REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE
   INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR
   IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed
   to pertain to the implementation or use of the technology
   described in this document or the extent to which any license
   under such rights might or might not be available; nor does it
   represent that it has made any independent effort to identify any
   such rights.  Information on the procedures with respect to
   rights in RFC documents can be found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use
   of such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository
   at http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention
   any copyrights, patents or patent applications, or other
   proprietary rights that may cover technology that may be required
   to implement this standard.  Please address the information to the
   IETF at ietf-ipr@ietf.org.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.









Ogier, et al.                 Experimental                     [Page 46]